The Hard Bar

Key Features

	Does not interfere with convertible top operation.
	Fits full height and width of the interior.
	Is the tallest design available.
	Allows for full use of seat travel and tilt.
	Constructed of high quality 1020 DOM tubing (1 1/2 diameter)
	Standard durable semi-flat black baked on finish. Polished Stainless Steel available.
	Complete installation instructions sheet included along with all other hardware needed.
	Works with the '99 thru 2005! Sorry - will not work with the 2006+ models.

Installation Information

	4-point mounting, no drilling required.
	First set of mounting plates rests on base plate that sits on top of a chassis box.
	Second set of plates are located approximately halfway up the legs of the main hoop and tie into top of the seat belt using existing shoulder harness hardware.
	The plastic panels covering the seat belt towers must be trimmed 1 3/8 inches from the top of the tower, down. May also be necessary to trim where the seat belt comes out of the tower.
	Tools Needed: 16mm (or 5/8 socket) wrench 2 - 9/16 wrenches 10 mm wrench or deep socket Phillips head screwdriver Tin snips (to trim panels) T-40 Torx Drive 6 pt.
	Complete Instructions

Description	Stock #	Price	S&H**
Hard Bar Black Powder Coated Finish	TM-500	$215	$40
Hard Bar Polished Stainless Steel	TM-504	$485	$40
Black Leather cover with Custom Formed High Density Padding	TM-535	$125	$16 * note below
Black Vinyl cover with Custom Formed High Density Padding	TM-537	$85	$16 * note below
Custom Formed High Density Padding For Hard Bar and Hard Sport bars NO COVER	HD-CS-PAD	$45	$16*
Traditional Race Type Roll Bar Padding - 30 inch stick - in Black	HD-FPAD-B	$10	$16*
Traditional Race Type Roll Bar Padding - 30 inch stick - in Red	HD-FPAD-R	$10	$16*
High Density SFI Race Type Roll Bar Padding 30 inch stick - in BLACK Straight length only - Meets SCCA Requirements & used by NASCAR	HD-HDSFI	$20	$16*

Description

Stock #

Price

S&H**

Hard Bar Black Powder Coated Finish

TM-500

$215

$40

Hard Bar Polished Stainless Steel

TM-504

$485

$40

Black Leather cover with
Custom Formed High Density Padding

TM-535

$125

$16 *
note below

Black Vinyl cover with
Custom Formed High Density Padding

TM-537

$85

$16 *
note below

Custom Formed High Density Padding
For Hard Bar and Hard Sport bars
NO COVER

HD-CS-PAD

$45

$16*

Traditional Race Type Roll Bar Padding - 30 inch stick - in Black

HD-FPAD-B

$10

$16*

Traditional Race Type Roll Bar Padding - 30 inch stick - in Red

HD-FPAD-R

$10

$16*

High Density SFI Race Type Roll Bar Padding 30 inch stick - in BLACK Straight length only
- Meets SCCA Requirements & used by NASCAR

HD-HDSFI

$20

$16*

THE HARD BAR

The Original

The original is Street and Solo II designed for ease of installation with the least amount of interference to normal use of your Miata.

Key Features

Does not interfere with convertible top operation.

Fits full height and width of the interior.

Is the tallest design available.

Allows for full use of seat travel and tilt.

Constructed of high quality 1020 DOM tubing (1 1/2 diameter)

Standard durable semi-flat black baked on finish. Polished Stainless Steel available.

Complete installation instructions sheet included along with all other hardware needed.

Works with the '99 thru 2005!
Sorry - will not work with the 2006+ models.

Installation Information

4-point mounting, no drilling required.

First set of mounting plates rests on base plate that sits on top of a chassis box.

Second set of plates are located approximately halfway up the legs of the main hoop and tie into top of the seat belt using existing shoulder harness hardware.

The plastic panels covering the seat belt towers must be trimmed 1 3/8 inches from the top of the tower, down. May also be necessary to trim where the seat belt comes out of the tower.

Tools Needed:
   16mm (or 5/8 socket) wrench
   2 - 9/16 wrenches
   10 mm wrench or deep socket
   Phillips head screwdriver
   Tin snips (to trim panels)
   T-40 Torx Drive 6 pt.

Note the differences between the Hard Bar and the Sport Bar.

The Hard Bar (top) has no back bracing while the Sport Bar does

Frequently Asked Questions about Hard Dog Roll Bars

Pricing
Note - Because of the many different models of Hard Dog roll bars, they are shipped directly from the factory per your order. Expect at least 3 to 5 weeks for delivery (Leather Covered bars may take longer).

THE HARD BAR

The Original

The original is Street and Solo II designed for ease of installation with the least amount of interference to normal use of your Miata.

Key Features

Does not interfere with convertible top operation.

Fits full height and width of the interior.

Is the tallest design available.

Allows for full use of seat travel and tilt.

Constructed of high quality 1020 DOM tubing (1 1/2 diameter)

Standard durable semi-flat black baked on finish. Polished Stainless Steel available.

Complete installation instructions sheet included along with all other hardware needed.

Works with the '99 thru 2005! Sorry - will not work with the 2006+ models.

Installation Information

4-point mounting, no drilling required.

First set of mounting plates rests on base plate that sits on top of a chassis box.

Second set of plates are located approximately halfway up the legs of the main hoop and tie into top of the seat belt using existing shoulder harness hardware.

The plastic panels covering the seat belt towers must be trimmed 1 3/8 inches from the top of the tower, down. May also be necessary to trim where the seat belt comes out of the tower.

Tools Needed: 16mm (or 5/8 socket) wrench 2 - 9/16 wrenches 10 mm wrench or deep socket Phillips head screwdriver Tin snips (to trim panels) T-40 Torx Drive 6 pt.

Note the differences between the Hard Bar and the Sport Bar.

The Hard Bar (top) has no back bracing while the Sport Bar does

Frequently Asked Questions about Hard Dog Roll Bars

Pricing Note - Because of the many different models of Hard Dog roll bars, they are shipped directly from the factory per your order. Expect at least 3 to 5 weeks for delivery (Leather Covered bars may take longer).

Works with the '99 thru 2005!
Sorry - will not work with the 2006+ models.

Tools Needed:
16mm (or 5/8 socket) wrench
2 - 9/16 wrenches
10 mm wrench or deep socket
Phillips head screwdriver
Tin snips (to trim panels)
T-40 Torx Drive 6 pt.

Pricing
Note - Because of the many different models of Hard Dog roll bars, they are shipped directly from the factory per your order. Expect at least 3 to 5 weeks for delivery (Leather Covered bars may take longer).